전선 교정 및 절단기 선택
Before you choose a 와이어 교정 및 절단기, send the supplier your wire grade and strength data as well as its diameter. Two coils of the same diameter can need different processing conditions. The right choice must deliver straight, usable cut pieces from your actual material.
Why a diameter range is only the first check
A machine listed for your wire diameter is a candidate, not yet a confirmed match. You still need to establish what material the rating covers, how the wire was processed, and the quality you need after cutting.
For example, a change from smooth drawn wire to ribbed reinforcing steel changes the information a supplier needs. Surface profile, material strength and incoming coil condition all belong in the enquiry. A previous test on another wire cannot confirm the result for yours.
Ask one direct question: “What material and strength range was this diameter capacity based on?” If the answer only repeats the maximum diameter, the selection is still incomplete.

와이어 교정 및 절단기

와이어 교정기
Check the feeding and straightening arrangement against your wire material and surface requirements. The configuration shown is a product example.
Read the strength figures correctly
Yield strength describes the start of permanent deformation; some certificates report a proof strength instead. Tensile strength, often marked Rm, describes the maximum tensile stress reached in a tensile test. They are different properties, as explained in ZwickRoell’s tensile testing guide.
In practical terms, the straightening process must change the wire’s shape permanently while controlling how much it springs back. The supplier therefore needs the material condition and yield or proof strength, not just its tensile strength. Cutting suitability also needs confirmation for that material and the proposed cutting unit.
Send the original certificate values and units. MPa and N/mm² are equivalent, but “high tensile” on its own is not a usable specification. If a certificate shows only a minimum value, ask the steel supplier for the actual test result or available range. Do not substitute a grade number for a measured tensile strength.
Build a material brief before comparing models
You do not need a long technical report. A clear material brief lets suppliers compare the same job.
| Information to provide | What it helps confirm |
|---|---|
| Steel grade, delivery condition and material certificate | The material being selected for, including reported strength values. |
| Diameter range and smooth or ribbed surface | Feeding, straightening and tooling suitability across your orders. |
| Coil weight and inside and outside dimensions | Whether the proposed payoff and handling arrangement fit your coils. |
| Required cut lengths and length tolerance | The cutting and collection requirements for the finished pieces. |
| Straightness requirement and surface limits | How finished-wire quality will be checked and accepted. |
| Typical order quantities and downstream use | A production target based on usable pieces rather than maximum feed speed. |
You can use the RKM wire straightening and cutting machine range to start a discussion. Ask for the proposed model and configuration to be confirmed against this brief. Do not combine the largest diameter from one model with the highest speed from another.
Define what a usable cut piece looks like
For a mesh producer, a piece is useful when it can enter the next operation consistently. Correct length alone is not enough if the wire is bowed, difficult to position or visibly damaged.
Agree on how straightness will be measured, including the inspected length, support arrangement and permissible deviation. Keep that requirement separate from cut-length tolerance. Also state whether marks on smooth wire, damage to ribs or cutting burrs would make a piece unacceptable.
For a line using pre-cut wire, check these requirements with the welding-machine supplier too. The wire needs to suit the feeding arrangement, not merely look straight in a photograph.
Use a sample test to close the remaining questions
Ask the supplier to test representative production material, including the more demanding grades or diameters you expect to buy. Identify each sample by its material certificate. If a substitute material is used, record the difference and what remains unconfirmed.
Agree on the test duration, sample quantities and acceptance checks before the run. Record the material, cut length, configuration, operating speed, accepted pieces and rejects. Inspect length, straightness, surface condition and cut ends using the agreed methods.
A short video can show feeding and collection. Measurements and production records answer whether the result meets your order. Ask for accepted pieces over the recorded run; keep an uninterrupted test rate separate from a full-shift output estimate that includes coil changes and handling.
구매자들이 자주 묻는 질문
Can one machine process both smooth and ribbed wire?
Possibly, if the proposed configuration is suitable for both. Give the supplier the grade, strength and diameter of each material. Ask what changes are needed and verify the result on samples, including any limits on surface marking or rib damage.
What if I do not have a material certificate?
Ask your wire supplier for one. You can begin a discussion with the grade, delivery condition, diameter and intended use, but the material match remains provisional until suitable evidence or testing is available.
Does a larger motor solve a high-strength wire problem?
Motor power alone does not confirm suitability. Feeding, the straightening arrangement, cutting capacity and tooling must work with the material. Compare the proposed configuration and test result rather than choosing by motor rating alone.
Can I keep the same settings after changing wire suppliers?
Do not assume that a matching diameter means an identical input. Compare the material certificates and coil condition, then have trained operators verify the finished pieces using the machine’s approved setup procedure.
Is the advertised maximum speed my production speed?
Use it as a stated machine limit under specified conditions. Ask what speed and accepted output are expected for your material, cut length and collection arrangement. Short pieces and long pieces should not automatically share one output estimate.
Which information should I send first?
Start with the material grade or certificate, wire diameter, cut length and intended use. Add your target quantity and quality requirements when available. This gives the supplier a practical starting point without delaying the first conversation.
Discuss your wire with RKM
Send RKM your wire details, required cut length and intended use. If you have a material certificate, include it. Ask for a configuration proposal and a sample-test plan tied to those requirements before you place an order.